BMVSK - VP416, DEGADUR
- MSDS: BMVSK
- Manufacturer: DEGUSSA CORP
- Product Name: VP416, DEGADUR
- National Stock Number: 6520-00N029213
Product Identification
Product ID:VP416, DEGADUR
MSDS Date:05/09/1989
FSC:6520
NIIN:00N029213
MSDS Number: BMVSK
Responsible Party
RIDGEFIELD PARK, NJ 07660
US
Emergency Phone: 201-818-3706
Info Phone: 201-818-3706
Preparer: PROD SFTY COMPLIANCE COM
Cage: 8C791
Contractor
Telephone: 201-818-3706
Cage: 8C791
Ingredients
METHACRYLIC ACID, METHYL ESTER; (METHYL METHACRYLATE)
CAS: 80-62-6
RTECS: OZ5075000
Fraction By Weight: <50%
OSHA PEL 100 PPM
ACGIH TLV: 100 PPM
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
ACRYLIC ACID, 2-ETHYLHEXYL ESTER; (2-ETHYLHEXYL ACRYLATE).
CAS: 103-11-7
RTECS: AT0855000
Fraction By Weight: <20%
Hazards
LD50 LC50 Mixture:SEE INGREDIENTS
Routes of Entry: Inhalation:NO Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:FAIRLY LENGTHY EXPOSURE MAY CAUSE SKIN
AND EYE IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:EYES:RINSE OUT WITHOUT DELAY UNDER RUNNING COLD WATER FOR AT
LEAST 15 MIN, W/EYELIDS (PALPEBRAL FISSURE) OPENED, SEEK MD ADVICE.
INHAL:ENSURE VICTIM HAS AN AMPLE SUPPLY OF FRESH AIR & IS KEPT
QUIET & WARM. SUMMON MD. SKIN:WASH AFFECTED SKIN W/SOAP & WATER/IF
NECESSARY W/ETHANOL. INGEST:DRINK 2 GLASSES OF WATER. INDUCE VOMIT
BY STICKING FINGER DOWN THROAT. CALL MD. NEVER GIVE ANYTHING BY
(SUPDAT)
Fire Fighting
Flash Point Method:CC
Flash Point:51.0F,10.6C
Lower Limits:2.1%
Upper Limits:12.5%
Extinguishing Media:WATER MIST, CO2, FOAM, DRY POWDER, COVER WITH SAND.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT . COOL AFFECTED CONTAINERS WITH WATER TO
PREVENT CONTAINER FROM RUPTURING.
Unusual Fire/Explosion Hazard:VAPOR IS HEAVIER THAN AIR AND FORMS
EXPLOSIVE MIXTURE WITH AIR. EXPLOSION LIMITS (FOR MONOMER
COMPONENT):2.1- 12.5% BY VOLUME (1 ATM, 77F).
Accidental Release
Spill Release Procedures:DIKE AND ABSORB SPILL WITH ABSORBENT MATERIAL
(SAND, SAWDUST, VERMICULITE, ETC.) AND COLLECT IN LEAK PROOF
CONTAINER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORAGE OVER LONG PERIODS OF TIME ONLY
IN INHIBITED FORM. ADVISABLE TO USE WITHIN 6 MONTHS.
Other Precautions:CHECK INHIBITOR LEV AFTER 3 MONTHS & ADD MORE IF NEC.
PROTECT FORM LIGHT & CONTAM. INDOOR STORAGE SHOULD BE RESTRICTED TO
APPRVD AREAS W/OVERHEAD SPRINKLERS. GROUND ALL CONTRS WHEN POURING.
PROVIDE AD EQ VENT. AVOID ALL IGNIT SOURCES.
Exposure Controls
Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR WITH ORGANIC
VAPOR/ACID GAS CANISTER. SCBA DURING EMERGENCIES.
Ventilation:MECHANICAL (GENERAL): EXPLOSION PROOF. EXHAUST AT POINT OF
OPERATION.
Protective Gloves:NEOPRENE GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:WEAR PROT CLTHG MADE FROM ANTI-STATIC, NON
MELTING MATLS. SAFETY SHOWER & EYE BATH SHOULD BE PROVIDED IN WORK
AREA.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
APPEAR/ODOR:(SWEET ESTER ODOR). MATL TO AVOID:STRONG SOLVENT ACTION &
CAN SOFTEN PAINT & RUBBER. FIRST AID PROC: MOUTH TO AN UNCONSCIOUS
PERSON. CLOTHING:REMOVE CONTAM CLTHG, WASH AFFECTED SKIN AREA W
/SOAP & WATER. THE FOLLOWING INFORMATION IS BASED ON ING 1:VP:
30.4. BP:212F. VD:>1. SOL IN H2O:15 G/L @ 77F.
Chemical Properties
HCC:F3
Boiling Pt:B.P. Text:SUPDAT
Vapor Pres:SUPDAT
Vapor Density:SUPDAT
Spec Gravity:0.97-.05
Evaporation Rate & Reference:>1 (BU AC = 1)
Solubility in Water:SUPDAT
Appearance and Odor:LOW VISCOUS, HIGHLY TURBID FLUID W/TYPICAL METHYL
METHACRYLATE ODOR (SUPDAT)
Stability
Stability Indicator/Materials to Avoid:YES
RADICAL SOURCES SUCH AS PEROXIDES, AZOCOMPOUNDS, AMINES, SULFUR
COMPOUNDS, HVY METAL IONS, ALKALIS. MATL HAS (SUPDAT)
Stability Condition to Avoid:AVOID BUILD UP OF ELECTROSTATIC CHARGES &
IGNIT SOURCES, ENSURE ADEQ SUPPLY OF FRESH AIR. AVOID CONTAM
W/FOREIGN MATLS.
Hazardous Decomposition Products:NONE
Conditions to Avoid Polymerization:EXCESSIVE HEAT, INADVERTENT ADDITION
OF RADICAL SOURCE TYPE CATALYSTS.
Disposal
Waste Disposal Methods:POLYMERZATION TO SOLID WITH PEROXIDES AND
MINERAL FILLER, OR IF RECYCLING IS IMPRACTICAL, WASTE DISPOSAL IN
ACCORDANCE WITH LOCAL, STATE & FEDERAL LEGISLATION AND REGULATIONS
(NOTIFY AUTHORITIES IF RE QUIRED TO DO SO).
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.